retention time comes up often in conversation and rarely with the context attached. Here we lay out the basics in order, then work through the practical considerations.
Updated 2026-04-23. Numbers and descriptions here follow the published literature rather than marketing material.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. A diode array detector records full spectra across a wavelength range, which helps identify co-eluting peaks. Mass spectrometry provides mass-to-charge ratios and can confirm molecular identity at low concentrations. The choice of detector depends on analyte structure, required sensitivity, and whether quantitation or identification is the goal. No single detector works for every compound, and method development often compares responses before selecting one.
High-performance liquid chromatography is an analytical technique that separates components of a liquid sample by passing it through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in interaction with the stationary phase cause analytes to migrate at different rates. Detectors record elution as peaks, and a data system converts signals into a chromatogram. The method is suited to compounds that dissolve in a liquid and are not volatile enough for gas chromatography.
Routine quality control includes blanks, duplicates, spiked samples, and certified reference materials. Calibration curves are prepared with standards at several concentrations, and the detector response is checked for linearity. Carryover, column aging, mobile phase evaporation, and temperature drift can shift retention times or peak areas. Maintenance such as replacing seals, filters, and columns helps prevent failures. Records of injections, integration, and deviations support traceability. Audits may request raw data and instrument logs for each batch.
Developing an HPLC test begins with defining the analytes, matrix, and required reporting limits. Chemists select a separation mode, column chemistry, mobile phase composition, flow rate, and detection wavelength or mass transition. Experiments then adjust these variables to achieve adequate retention, resolution, and peak shape. System suitability tests confirm that the instrument and method perform consistently before sample analysis. Without suitable resolution, quantitative results may be unreliable. Preliminary runs often use scouting gradients to locate retention windows.
Validation establishes that a method is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, robustness, and stability of standards and samples. Acceptance criteria are defined in advance, and results are documented in a validation report. Regulatory guidance for pharmaceuticals, foods, and environmental testing differs, so the applicable framework must be identified. Ongoing verification uses control samples and trend charts after validation. Method transfer to another laboratory may require partial revalidation.
| Property | Value | Notes |
|---|---|---|
| Separation mode | Reversed-phase | Most common for neutral and moderately polar analytes |
| Column particle size | 3–5 µm | Smaller particles improve resolution but raise backpressure |
| Mobile phase pH range | 2–8 | Silica-based columns may degrade outside this range |
| Typical flow rate | 1.0–2.0 mL/min | For analytical columns with 4.6 mm internal diameter |
| Common synonyms | HPLC, LC, high-pressure liquid chromatography | High-performance liquid chromatography is the standard expansion |
Practical HPLC testing depends on careful sample preparation and instrument maintenance. Samples may require filtration, dilution, pH adjustment, or extraction to avoid column damage and matrix interference. Mobile phases are degassed and filtered, and columns are equilibrated before injection. Common problems include peak tailing, baseline drift, ghost peaks, carryover, and co-elution of analytes. Documentation of instrument logs, calibration records, and electronic audit trails supports data integrity and traceability. Ongoing training and routine maintenance help reduce variability between analysts and laboratories.
Quality control laboratories use HPLC to check identity, purity, concentration, and stability of raw materials and finished products. A validated method specifies the column, mobile phase, flow rate, detection wavelength, injection volume, and run time. Samples are prepared and compared against reference standards of known concentration. The resulting chromatogram provides quantitative data, such as assay values and impurity levels. This approach is common in pharmaceutical, food, environmental, and industrial testing where consistent measurements are required.
Method validation demonstrates that an analytical procedure is suitable for its intended purpose. Typical validation characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulatory guidance from bodies such as the International Council for Harmonisation and the United States Pharmacopeia outlines expectations, though specific criteria depend on the product and method. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, column efficiency, and injection repeatability. Failure of these checks can invalidate a batch of measurements.
Laboratories apply HPLC testing across pharmaceutical, food, environmental, and industrial chemistry. The method can measure active ingredients, impurities, additives, preservatives, and degradation products. Sample preparation often includes dilution, filtration, and sometimes extraction or derivatization. The choice of column, mobile phase, pH, temperature, and detector depends on the analytes and matrix. Results are compared with reference standards to assign identity and concentration. Method suitability is judged by resolution, precision, and accuracy.
HPLC testing is not a single fixed procedure; it is a family of separation modes. Reversed-phase, normal-phase, ion-exchange, size-exclusion, and affinity chromatography each suit different analyte properties. Reversed-phase methods dominate because they handle many neutral and moderately polar compounds. Detection can be optical, electrochemical, or mass spectrometric, and the detector dictates what information is available. Coupling with mass spectrometry increases selectivity and enables identification when standards are unavailable. The technique cannot separate every mixture without adjustment.
HPLC testing is an analytical technique used to separate, identify, and quantify components in a liquid sample. It relies on a pressurized mobile phase that carries the sample through a column packed with stationary phase. Different compounds travel at different rates because of interactions with the stationary and mobile phases. The resulting signal versus time is a chromatogram. Peak position indicates identity under specified conditions, while peak area or height relates to amount.
Documentation and traceability are central to regulated HPLC testing. Records typically include instrument logs, column history, mobile-phase preparation, sample preparation, injection sequences, raw chromatograms, and audit trails. Electronic systems may require user access controls, time-stamped changes, and backup procedures. Training records show that analysts are qualified for assigned methods. Audits and inspections check whether written procedures match actual practice and whether deviations are documented. These controls support reproducibility and allow results to be reconstructed if questions arise later.
Method validation establishes that an HPLC procedure is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, robustness, and solution stability. Accuracy reflects closeness to a reference value, while precision reflects agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from matrix components. Validation is documented through protocols and reports, and the required extent depends on the method's use and regulatory context.
Bruce Glick grew up in Pittsburgh, Pennsylvania and was interested in birds as a child. His father, Peter Glick, was the Secretary of Labor for Pennsylvania. Glick served in World War II. He went to Rutgers University and studied birds majoring in poultry science, graduating in 1951. In 1950 he married Kay McCall. He received an M.S. degree from the University of Massachusetts in genetics in 1952 and attended Ohio State University as a Ph.D. student, graduating with a PhD in physiology in 1955. While there, he worked on determining the purpose of the Bursa of Fabricius, a gland that he was able to remove from a goose without any apparent effect. A fellow graduate student, Timothy Chang, worked with Glick's geese in a different study, and noticed that the birds without the Bursa of Fabricius did not produce expected antibodies. Glick and Chang wrote up the results of this study and were unable to get it published in Science, so it was published in Poultry Science in 1956. Their publication, considered a landmark paper, is one of the most cited works from Poultry Science.
ADAM17 is an 824-amino acid polypeptide. ADAM17 has multidomain structure that includes a pro-domain, a metallo-protease domain, a disintegrin domain, a cysteine-rich domain, an EGF-like domain, a transmembrane domain, and a cytoplasmic tail. The metalloprotease domain is responsible for the enzyme's catalytic activity, cleaving membrane-bound proteins, including cytokines like TNF-alpha, to release their soluble forms. The disintegrin and cysteine-rich domains are implicated in cell adhesion and interaction with integrins, while the transmembrane domain anchors the protein in the membrane. The cytoplasmic tail is involved in intracellular signaling and protein-protein interactions. ADAM17's activity is tightly regulated through multiple mechanisms, including the removal of its pro-domain and interactions with regulatory proteins such as TIMPs (tissue inhibitors of metalloproteinases).
The bioanalyst deals with complex biological samples containing the analyte alongside a diverse range of chemicals that can have an adverse impact on the accurate and precise quantification of the analyte. As such, a wide range of techniques are applied to extract the analyte from its matrix. These include: Protein precipitation Liquid–liquid extraction Solid phase extraction Bioanalytical laboratories often deal with large numbers of samples, for example resulting from clinical trials. As such, automated sample preparation methods and liquid-handling robots are commonly employed to increase efficiency and reduce costs.
Different genotypes may compete with each other in a way that is not beneficial for the population. A pure line optimized for a certain environment or usage outperforms the CCP under these specific conditions. There is no reason to believe that the Darwinian selection will work in the desired direction for traits such as baking quality. Natural selection and in-field human selection act on the plant stage, not the seed stage. Common Bunt is a seed borne disease in wheat. In conventional farming it is controlled by fungicide treatment of seeds. In organic farming seeds can be cleaned by brushing before sowing, but it is also desirable that plants have genetic resistance. A CCP, including crosses of resistant cultivars, was grown with heavy common bunt infection for 5 years and it appeared to get more resistant, but the common bunt's virulence appeared to change at least as fast. The overall result was that infection levels went up.
Laboratory testing in the United States is subject to federal regulation. Clinical laboratories performing testing are overseen by the Centers for Medicare and Medicaid Services (CMS) utilizing national standards established under the Clinical Laboratory Improvement Amendments (CLIA). The Centers for Disease Control and Prevention (CDC) and the Food and Drug Administration (FDA) assist CMS in this process. CMS ensures the integrity of laboratories performing testing via inspections and consistent oversight, bolstered with proficiency testing by accredited organizations. CLIA authorizes regulation of laboratories that conduct testing, not the individuals who order the tests or receive test results. All laboratories performing DTC testing must obtain CLIA certification and maintain compliance with national standards.
Sources: en.wikipedia.org
During the development of B cells, the immunoglobulin gene undergoes sequences of rearrangements that lead to formation of the antibody repertoire. For example, in the early stages of transition from pro-B cell to pre-B cell, a partial rearrangement of the heavy-chain gene occurs which is followed by complete rearrangement of heavy-chain gene. At this stage (Pre-B cell), the μ heavy chain and surrogate light chain are formed. The final rearrangement of the light chain gene generates immature B cell and membrane-bound IgM (mIgM). The process explained here occurs during development of naïve B cells, prior to exposure to exogenous antigens. The mature B cell formed as a result of these processing changes leaves the bone marrow and may then be stimulated by an antigen to develop into antibody-secreting plasma cells. Also at first, the mature B cell expresses membrane-bound IgD and IgM. These two classes could switch to secretory IgD and IgM during the processing of mRNAs. Finally, further class switching follows as the cell continues to divide and differentiate. For instance, a B cell expressing IgM can switch to IgG, IgA, or IgE depending on the stimulus provided (which may be dependent upon the antigenic source and the responding immune cells).
The terms "active" and "passive" are simple but important terms in the world of automotive safety. "Active safety" is used to refer to technology assisting in the prevention of a crash and "passive safety" to components of the vehicle (primarily airbags, seatbelts and the physical structure of the vehicle) that help to protect occupants during a crash. Crash avoidance systems and devices help the driver — and, increasingly, help the vehicle itself — to avoid a collision. This category includes: The vehicle's headlamps, reflectors, and other lights and signals The vehicle's mirrors The vehicle's brakes, steering, and suspension systems A subset of crash avoidance is driver assistance systems, which help the driver to detect obstacles and to control the vehicle. Driver assistance systems include:
Bodybuilding supplements are dietary supplements commonly used by those involved in bodybuilding, weightlifting, mixed martial arts, and athletics for the purpose of facilitating an increase in lean body mass. Bodybuilding supplements may contain ingredients that are advertised to increase a person's muscle, body weight, athletic performance, and decrease a person's percent body fat for desired muscle definition. Among the most widely used are high protein drinks, pre-workout blends and caffeinated energy drinks, branched-chain amino acids (BCAA), glutamine, arginine, essential fatty acids, creatine, HMB, whey protein, ZMA, and weight loss products. Supplements are sold either as single ingredient preparations or in the form of "stacks" – proprietary blends of various supplements marketed as offering synergistic advantages.
Upregulation of receptors is the increase in receptor number or sensitivity of receptors. The receptors involved in functional antagonism are regulated in sensitivity, number and location. Therefore, changes in receptors are common. Using a long-term antagonist drug or continuous exposure to an antagonist may cause the upregulation and hypersensitivity of receptors, which means an increase in the number and sensitivity of receptors. The increase in the number of receptors is due to the increased expression of receptors after prolonged inhibition. The upregulation of receptors is important in the clinical aspect. One example of upregulation of receptors is the upregulation of β-receptors caused by β receptor antagonists (also called β-blocker). The prolonged use of β-blockers results in the blockade of β-receptors, causing cells (mainly myocardial cells) to increase their expression of β-receptor. After removing the blockage, more receptors available for stimulation, resulting in higher sensitivity of β-receptors called the hypersensitivity of β-receptors. Abrupt discontinuation of β-blocker may potentially aggravate coronary artery disease, tachycardia, or even sudden cardiac death. Therefore, to prevent the adverse effects, doses of β-blocker must be reduced gradually over 10–14 days.
12(S)-HpETE, 12(R)-HETE, racemic mixtures of these 12-HETEs, and/or 12-oxo-ETE stimulate: a) the directed migration (chemotaxis) of human, rat, and rabbit neutrophils as well as rabbit macrophages; b) human neutrophils to adhere to each other (i.e. aggregate) and in cooperation with tumor necrosis factor alpha or platelet-activating factor, to release their granule-bound enzymes; c) the binding of human vascular epithelial cells to human monocytes; d) DNA synthesis and mitogenesis in the immortalized human keratinocyte cell line HaCaT; and e) when injected in the skin of human volunteers, the extravasation and local accumulation of circulating blood neutrophils and mononuclear cells. These results suggest these metabolites contribute to the inflammation that occurs at sites where they are formed in abnormal amounts such as in human rheumatoid arthritis, inflammatory bowel disease, contact dermatitis, psoriasis, various forms of ichthyosis including congenital ichthyosiform erythroderma, and corneal inflammatory diseases. Since BLT2 appears to mediate the responses of leukocytes to 12(S)-HpETE, 12(S)-HETE, 12(R)-HETE, and 12-oxo-ETE but GPR31 is expressed by various other cells (e.g. vascular endothelium) involved in inflammation, the pro-inflammatory actions of 12-HETE in humans may involve both types of G protein-coupled receptors.
Sources: en.wikipedia.org
AREs are recognized by RNA binding proteins such as tristetraprolin (TTP), AUF1, and Hu Antigen R (HuR). RNA-binding proteins that bind AREs have been termed ARE-BPs and as of 2019, about 20 ARE-BPs have been identified. Although the exact mechanism is not very well understood, recent publications have attempted to propose the action of some of these ARE-BPs. One characteristic of many ARE-BPs is that they can shuttle between the nucleus and cytoplasm and exert different functions to control gene expression based on their subcellular location. AUF1, also known as hnRNP D, binds AREs through RNA recognition motifs (RRMs). AUF1 is also known to interact with the translation initiation factor eIF4G and with poly(A)-binding protein, indicating that AUF1 senses the translational status of mRNA and decays accordingly through the excision of the poly(A) tail.
Elimination of protruding knobs and controls in passenger compartment Additional padding on the instrument panel and other interior surfaces Mounting points for front outboard shoulder belts Four-way hazard flashers A uniform P-R-N-D-L gear sequence for automatic transmission gear selectors Dual-circuit brake hydraulic systems In 1968, the precursor agency to the US National Highway Traffic Safety Administration's first Federal Motor Vehicle Safety Standards took effect. These required shoulder belts for left and right front-seat vehicle occupants, side marker lights, collapsible steering columns, and other safety features. 1969 saw the addition of head restraints for front outboard passengers, addressing the problem of whiplash in rear-end collisions. These safety requirements did not apply to vehicles classified as "commercial," such as light-duty pickup trucks. Thus, manufacturers did not always include such hardware in these vehicles, even though many did passenger-car duty. Volvo developed the first rear-facing child seat in 1964 and introduced its own booster seat in 1978.
An insulin pump delivers insulin subcutaneously. The insulin pump body itself can also contain the algorithm used in an AID system, or it can connect via Bluetooth with a separate mobile device (such as a phone) to send data and receive commands to adjust insulin delivery. Algorithm The algorithm for each AID system differs. In commercial systems (see below), little is known about the details of how the control algorithm works. In open source systems, the code and algorithm are openly available. In general, all algorithms do the same basic functionality of taking in CGM data and based on predicted glucose level's and the user's personal settings (for basal rates, insulin sensitivity, and carbohydrate ratio, for example) then recommends insulin dosing to help bring or maintain glucose levels in target range. Depending on the system, users may have the ability to adjust the target for the system, and may have different settings to ask the system to give more or less insulin in general.
The polar, uncharged amino acids serine (Ser, S), threonine (Thr, T), asparagine (Asn, N) and glutamine (Gln, Q) readily form hydrogen bonds with water and other amino acids. They do not ionize in normal conditions, a prominent exception being the catalytic serine in serine proteases. This is an example of severe perturbation, and is not characteristic of serine residues in general. Threonine has two chiral centers, not only the L (2S) chiral center at the α-carbon shared by all amino acids apart from achiral glycine, but also (3R) at the β-carbon. The full stereochemical specification is (2S,3R)-L-threonine. Because of the presence of phenolic hydroxyl group with a pKa = ~10, tyrosine is best classified as a neutral polar amino acid, but with amphipathic character that makes it less polar than classical small polar amino acid residues. Nonpolar amino acid interactions are the primary driving force behind the processes that fold proteins into their functional three dimensional structures. None of these amino acids' side chains ionize easily, and therefore do not have pKas.
Sources: en.wikipedia.org
HPLC testing separates and quantifies components in a liquid sample. It is used to check identity, purity, concentration, or stability. The technique works best for compounds that dissolve and are not easily vaporized.
The pump maintains a steady flow rate and pressure, which keeps retention times reproducible. Pulsation or flow errors can shift peaks and distort quantitation. Modern pumps use feedback control to reduce these variations.
HPLC alone usually separates compounds but does not always identify them. Retention time matching with a known standard provides tentative identification. Coupling HPLC to mass spectrometry adds mass information that supports structural identification.
System suitability is a set of checks performed before and during a run to confirm that the instrument, column, and method work as expected. Common checks include resolution, tailing factor, theoretical plates, and relative standard deviation of replicate injections. Failure triggers troubleshooting or method adjustment.