This is a working overview of reference standard, written for readers who want more than a one-paragraph summary but less than a textbook.
Reviewed 2025-08-21. Anything still debated is marked as such rather than presented as settled.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample by passing them through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in how analytes partition between the mobile phase and the stationary phase cause them to exit the column at different times. Detection then records a signal proportional to the amount of each separated substance. The resulting chromatogram provides retention times and peak areas for identification and quantification.
Validation demonstrates that a method is suitable for its intended use. Typical performance characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulators and standards organizations provide frameworks, but specific requirements depend on the application and jurisdiction. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, retention time repeatability, and sensitivity. A validated method is not permanently fixed; changes may require partial or full revalidation.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
| Property | Value | Notes |
|---|---|---|
| Separation principle | Differential partitioning | Analytes distribute between mobile and stationary phases. |
| Mobile phase | Liquid solvent mixture | Composition controls retention and selectivity. |
| Stationary phase | Packed column particles | Often chemically bonded silica. |
| Typical detector | UV-Vis or photodiode array | Mass spectrometry is also common. |
| Common synonym | High-performance liquid chromatography | Abbreviated as HPLC. |
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Method validation demonstrates that an analytical procedure is suitable for its intended purpose. Typical validation characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulatory guidance from bodies such as the International Council for Harmonisation and the United States Pharmacopeia outlines expectations, though specific criteria depend on the product and method. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, column efficiency, and injection repeatability. Failure of these checks can invalidate a batch of measurements.
Practical HPLC testing depends on careful sample preparation and instrument maintenance. Samples may require filtration, dilution, pH adjustment, or extraction to avoid column damage and matrix interference. Mobile phases are degassed and filtered, and columns are equilibrated before injection. Common problems include peak tailing, baseline drift, ghost peaks, carryover, and co-elution of analytes. Documentation of instrument logs, calibration records, and electronic audit trails supports data integrity and traceability. Ongoing training and routine maintenance help reduce variability between analysts and laboratories.
Quality control for HPLC testing combines scheduled checks, documented procedures, and review of results. Before sample analysis, system suitability testing confirms that the instrument, column, and method meet predefined criteria. Common criteria include resolution between critical peaks, retention time precision, peak tailing, and theoretical plate count. Failure triggers investigation before results are reported. Records link raw data, calculations, instrument logs, and analyst identity to each batch, supporting audits and repeat analysis.
Method validation evaluates accuracy, precision, specificity, linearity, range, detection limit, quantitation limit, and robustness. Regulatory guidance for pharmaceuticals, foods, and environmental testing defines expected documentation and acceptance criteria. Verification confirms that a validated method works in a specific laboratory with its own instruments and reagents. Calibration curves use reference standards with known purity and traceability, while measurement uncertainty is estimated from validation data, control charts, and collaborative studies. The scope of validation depends on the method's intended use.
In March 2003, Cambridge Antibody Technology (CAT) stated its wish to "initiate discussions regarding the applicability of the royalty offset provisions for Humira" with Abbott Laboratories in the High Court of London. In November 2004, the trial began, and in December 2004, Justice Hugh Laddie ruled for CAT. A short version of the full statement of the proceedings was released. In it Justice Laddie remarked, "Abbott was in error when it made its first royalty payment to CAT calculated on the basis that only 2% of the Net Sales was due. It should have calculated on the basis of the full royalty of just over 5% and should have paid and continued to pay CAT accordingly." Justice Laddie went on to observe "...that the construction advanced by Abbott does violence to the language of the agreements, renders them obscure and makes little or no commercial sense. For this reason CAT wins the action." Abbott was required to pay CAT US$255 million, some of which was to be passed to its partners in development. Of this sum, the Medical Research Council received US$191 million, and in addition, Abbott was asked to pay the MRC a further US$7.5 million over five years from 2006, providing that Humira remains on the market. The MRC also is to receive a further £5.1 million (sterling) in respect of past royalties.
The topology of a β-sheet describes the order of hydrogen-bonded β-strands along the backbone. For example, the flavodoxin fold has a five-stranded, parallel β-sheet with topology 21345; thus, the edge strands are β-strand 2 and β-strand 5 along the backbone. Spelled out explicitly, β-strand 2 is H-bonded to β-strand 1, which is H-bonded to β-strand 3, which is H-bonded to β-strand 4, which is H-bonded to β-strand 5, the other edge strand. In the same system, the Greek key motif described above has a 4123 topology. The secondary structure of a β-sheet can be described roughly by giving the number of strands, their topology, and whether their hydrogen bonds are parallel or antiparallel. β-sheets can be open, meaning that they have two edge strands (as in the flavodoxin fold or the immunoglobulin fold) or they can be closed β-barrels (such as the TIM barrel). β-Barrels are often described by their stagger or shear. Some open β-sheets are very curved and fold over on themselves (as in the SH3 domain) or form horseshoe shapes (as in the ribonuclease inhibitor). Open β-sheets can assemble face-to-face (such as the β-propeller domain or immunoglobulin fold) or edge-to-edge, forming one big β-sheet.
Cilengitide, a cyclic pentapeptide (RGDfV), is an investigational drug intended to block the growth of new blood vessels in tumors by interfering with the activation of integrin αVβ3. This integrin is upregulated in tumor and activated endothelial cells. This and other anti-angiogenic therapies depend on cutting off the blood supply to the tumor micro-environment, leading to hypoxia and necrosis. Cilengitide has been evaluated for the treatment of glioblastoma, but, as is the case for other anti-angiogenic therapies, has not been shown to alter progression or improve survival either alone or in combination with standard treatments. CEND-1, also known as iRGD, is a cyclic peptide that homes to tumors via binding to integrin alpha V receptors. It also binds and activates neuropilin-1, leading to a temporary opening of the tumor and an enhanced delivery of anti-cancer agents into the tumor tissue. It is currently being tested in clinical trials in solid tumor patients.
These drugs have been derived from NSAIDs. The cyclooxygenase enzyme inhibited by NSAIDs was discovered to have at least two different versions: COX-1 and COX-2. Research suggested most of the adverse effects of NSAdiated by blocking the COX-1 (constitutive) enzyme, with the analgesic effects being mediated by the COX-2 (inducible) enzyme. Thus, the COX-2 inhibitors were developed to inhibit only the COX-2 enzyme (traditional NSAIDs block both versions in general). These drugs (e.g., rofecoxib, celecoxib, and etoricoxib) are equally effective analgesics when compared with NSAIDs, but cause less gastrointestinal hemorrhage in particular. After widespread adoption of the COX-2 inhibitors, it was discovered that most of the drugs in this class increase the risk of cardiovascular events by 40% on average. This led to the withdrawal of rofecoxib and valdecoxib, and warnings on others. Etoricoxib seems relatively safe, with the risk of thrombotic events similar to that of non-coxib NSAID diclofenac.
Sources: en.wikipedia.org
The analytes are in the vapor phase. This includes breath, odors, VOCs, and other molecules with low volatility that, due to the constant improvements in sensitivity, are detectable in the vapor phase despite their low vapor pressure. Analyte ions are produced via gas-phase chemical reactions, where charging agents collide with the analyte molecules and transfer their charge. In secondary electro-spray ionization (SESI), a nano-electrospray operated at high temperature produces nanodroplets that evaporate very rapidly to produce ions and protonated water clusters that ionize the vapors of interest. SESI is commonly used for the analysis of trace concentrations of vapors being able to detect low volatility species in the gas phase with molecular masses of up to 700 Da.
ADP + Pi + 2H+out ⇌ ATP + H2O + 2H+in ATP synthase lies across a cellular membrane and forms an aperture that protons can cross from areas of high concentration to areas of low concentration, imparting energy for the synthesis of ATP. This electrochemical gradient is generated by the electron transport chain and allows cells to store energy in ATP for later use. In prokaryotic cells ATP synthase lies across the plasma membrane, while in eukaryotic cells it lies across the inner mitochondrial membrane. Organisms capable of photosynthesis also have ATP synthase across the thylakoid membrane, which in plants is located in the chloroplast and in cyanobacteria is located in the cytoplasm. ATP synthase is present in all organisms studied. Eukaryotic ATP synthases are F-ATPases (which usually work as ATP synthases instead of ATPases in cellular environments) and running "in reverse" for an ATPase (ATPases catalyze the decomposition of ATP into ADP and a free phosphate ion). This article deals mainly with this type. An F-ATPase consists of two main subunits, FO and F1, which has a rotational motor mechanism allowing for ATP production.
Overall, automated synthesis has improved the efficiency for the parallel synthesis and combinatorial methods of polymers. These techniques aim to design new materials, in addition to studying the relationships of their structure and properties. However, while screening for polymers enables this investigation, it becomes increasingly demanding for researchers to create the libraries for these synthetic compositions. In addition, preparation requires a large number of repetitive reactions to be completed, leading to an immense burden of planning and labor. Using automated synthesis, this process can be refined, increasing the efficiency of the reaction and removing the impact of human error.
2-Aminoisobutyric acid is not one of the proteinogenic amino acids and is rather rare in nature (cf. non-proteinogenic amino acids). In the context of cell-free protein synthesis 2-aminoisobutyric acid is compatible with ribosomal elongation of peptide synthesis. Flexizymes and an engineered tRNA body enhance the affinity of aminoacylated Aib-tRNA species to elongation factor P. The result was an increased incorporation of Aib into peptides in a cell free translation system. Iqbal et al.. used an alternative approach of creating an editing deficient valine—tRNA ligase to synthesize aminoacylated Aib-tRNAVal. The aminoacylated tRNA was subsequently used in a cell-free translation system to yield Aib-containing peptides. Aib has been found in meteorites and some antibiotics of fungal origin, such as alamethicin and some lantibiotics.
An automated synthesis is very similar in procedure to performing a manual synthesis. The overseeing chemist decides on a target molecule then formulates the experimental plan, which is a sequential series of steps. Then, they collect the required equipment and execute the plan. The automated synthesis follows the same pathway, except that the computer devises and executes the experimental plan. However, human revision is usually still required to ensure the automated route is practical and there are no implicit steps or conditions missing from the proposed procedure. In organic synthesis, organic synthesis software is used to automate the process of identifying sequences of reactions or routes that can be used to synthesize organic compounds.
Sources: en.wikipedia.org
Alcohol dehydrogenase class-3 is an enzyme that in humans is encoded by the ADH5 gene. This gene encodes glutathione-dependent formaldehyde dehydrogenase or the class III alcohol dehydrogenase chi subunit, which is a member of the alcohol dehydrogenase family. Members of this family metabolize a wide variety of substrates, including ethanol, retinol, other aliphatic alcohols, hydroxysteroids, and lipid peroxidation products. Class III alcohol dehydrogenase is a homodimer composed of 2 chi subunits. It has virtually no activity for ethanol oxidation, but exhibits high activity for oxidation of long-chain primary alcohols and for oxidation of S-hydroxymethyl-glutathione, a spontaneous adduct between formaldehyde and glutathione. This enzyme is an important component of cellular metabolism for the elimination of formaldehyde, a potent irritant and sensitizing agent that causes lacrymation, rhinitis, pharyngitis, and contact dermatitis.
Anne S. Ulrich (born December 31, 1966) is a German chemist. She is the director of the Institute of Biological Interfaces (IBG-2) and Chair of Biochemistry at the Karlsruhe Institute of Technology. She studied chemistry at the University of Oxford - continued her doctoral work in the laboratory of Anthony Watts - held subsequent research positions as an EMBO-Fellow with Hartmut Oschkinat at the European Molecular Biology Laboratory in Heidelberg and as a Liebig-Fellow with Felix Wieland at the University of Heidelberg - became Associate Professor at the University of Jena - until she moved her group in 2002 to the Karlsruhe Institute of Technology. Her research focuses on the structural and functional analysis of biomembranes by solid state NMR. The main systems of interest are:
Albert Pinhasov (Hebrew: אלברט פנחסוב; born 9 February 1972) is the Rector of Ariel University. He is a researcher in the fields of Molecular Psychiatry and Psychopharmacology.He also served as Vice President and Dean for Research & Development and the Head of the Department of Molecular Biology at Ariel University. Albert Pinhasov was born on 9 February 1972 in the city of Namangan, Uzbekistan. From 1990 to 1994, he studied at the Gorky Academy of Medicine, in the city of Nizhny Novgorod, Russia. In 1994, he immigrated to Israel where he continued his education at Tel Aviv University. He was awarded a Master of Science degree (MSc) in 1998 and a PhD in the field of Molecular Biology and Clinical Biochemistry under the mentorship of Illana Gozes in 2002 from Tel Aviv University.
n RCHNHC(O)OC(O) → [N(H)CH(R)CO)]n + n CO2 Poly-L-lysine has been prepared from N-carbobenzyloxy-α-N-carboxy-L-lysine anhydride, followed by deprotection with phosphonium iodide. Peptide synthesis from NCAs does not require protection of the amino acid functional groups. N-Substituted NCAs, such as sulfenamide derivatives have also been examined. The ring-opening polymerization of NCAs is catalyzed by metal catalysts. The polymerization of NCA’s have been considered as a prebiotic route to polypeptides. NCAs can also be used to form amides and lactams by reaction of carboxylic acids and isocyanates. Dakin–West reaction Glycine N-carboxyanhydride, the parent NCA
Sources: en.wikipedia.org
HPLC separates and detects individual compounds in a liquid sample, producing peaks at characteristic retention times. Peak area or height can be used to estimate concentration when calibrated with known standards. It does not identify unknown compounds with certainty unless additional detectors or reference materials are used.
Pressure drives the liquid mobile phase through a column packed with small particles. Without pressure, flow would be very slow or stop because the packed bed resists liquid movement. Modern pumps maintain a steady flow despite the resistance.
A chromatogram is a plot of detector signal against time after sample injection. Each peak represents a compound or group of compounds eluting from the column. Retention time and peak area are the main measurements read from the plot.
It is a set of checks performed before or during an HPLC run to confirm the system works as expected. Parameters may include resolution, tailing factor, theoretical plates, and retention time precision. Failure can trigger maintenance, method adjustment, or repeat analysis.